Product Review: Analyzing Reflectors: Lumenbrite III, Lumenmax Elite, Lumenmax, and Lumenarc III

by | Jan 15, 2009 | 0 comments

Since the last set of reflector tests a few more new reflectors have been introduced in the market. These new reflectors all carry the “Lumen” name – Lumenbrite, Lumenmax Elite, Lumenmax, similar to their predecessor the Lumenarc III, even though they are manufactured and marketed by different companies. This article presents test results on these new fixtures/reflectors. The reflectors were tested using the same setup and methodology as used for the tests on other reflectors, described in [1]. Previous reflector tests had data for light dispersions at 6″,9” and 12″. While this data allowed for a meaningful comparison between the reflectors, it could be argued these are not practical distances at which corals would be placed in the tank and data further from the lamp would be more useful. Further, there was speculation among hobbyists that some reflectors were better at projecting light further away from the reflector and hence making them more suitable for deeper tanks. To accommodate some of these concerns, measurements in this study have been made at 24″ and 30′ from the center of the lamp in the reflector. This article continues in a similar vein as the previous reflector articles and presents the data and analysis of these new reflectors in my inventory, and compares them to the Lumenarc III reflector.

Table 1, presents the information on the ballasts and lamp used to test all the reflectors. Since the same ballast and lamp is used, direct comparisons can be made between the reflectors. Table 2 lists the physical specifications of the reflectors, manufacturer, pictures and some comments on these reflectors.

Table 1: Listing of the Reflectors Tested
ReflectorBallastLamp
Lumenmax Elite400W Icecap Electronic BallastUshio 14000K 400W Mogul
Lumenbrite III
Lumenarc III
Lumenmax (Large)
Table 2: Specifications of the Reflectors tested
ReflectorSizeManufacturerPictureComments
Lumenarc III19.5″ x 19.5″ x 8.5″ tallPacific Garden SupplyBulb position can be adjusted to center bulb
Air Cooled option available
Accepts glass shield
Lumenbrite III20″ x 20″ x 9″ tallCoralvueOctagonal Shape
Does not accept glass shield
Lumenmax (large)22¼” x 22¼” x 8¾” tallSunlight SupplyCombination of textured and smooth facets
Cannot adjust for bulb length
Does not accept glass shield
Lumenmax Elite15″ x 15″ x 5″ tallSunlight Supplytextured reflective surface

Reflector Data and Analysis

The data plots for each reflector at the distances 24″ and 30″ are plotted as a surface graph, top view graph, and a % distribution graph to illustrate the intensity and spread at different points on the 36″X36″ measuring grid, with data recorded at 3″ intervals. The lamps are oriented so that they are parallel to the X-axis in the plots, with the center of the lamp aligned with (0,0). All measurements of distances are taken from the centerline of the lamp. Table 3 below shows the list of figures associated with each reflector.

Table 3: List of Figures associated with each reflector
ReflectorFigures
LumenMax EliteFigs. 1-3
LumenBrite IIIFigs. 4-6
LumenArc IIIFigs. 7-9
LumenMax (Large)Figs. 10-12

One of the measures of a reflector performance could be its ability to direct light into the aquarium. A reflector’s total incident light upon a surface of a given area is representative of the performance of a reflector. It is computed by adding up all the measurements taken at the discrete points within the region. It demonstrates how much light the reflector is able to focus downward when compared to other reflectors with similar operating conditions (same ballast and lamp). While it can be argued that adding all the PPFD values is technically not a valid measure as per the definition of PPFD (since PPFD is defined as microEinstiens/m2/sec), it can be used to provide a metric for reflector performance. Further summing over the data points on a given area can easily be used to compute the average, if so desired. Since the area under consideration is the same for all reflectors, we can just as well use the sum of the PPFD values distributed over this area (169 data points) instead of an average as a performance metric.

Table 4 presents this data for the reflectors in this article. Note that the initial PPFD values of the lamp/ballast combo used to test the reflector influences this data. For these tests, the Ushio 14000K 400W lamp used with the Icecap Electronic ballast has a PPFD reading of 151.7 at 18″. For any other ballast/lamp combo the PPFD data at 18″ can be obtained from the website http://reeflightinginfo.arvixe.com and the reflector data can be scaled appropriately. For example, if using a magnetic ballast with Ushio Blue 20000K lamp with a PPFD of 109 (from the data on the website), the reflector data can be scaled by 0.718 (109/151.7) to get a sense of the light values obtained with this combination.

Table 4: Total Incident PPFD on a given Surface area
Total Incident Light
ReflectorDistance:3×3 Area2×2 Area1×1 AreaMaximum PPFD:
LumenMax Elite24″332292613813571711
30″290802173510219519
LumenBrite24″357002821413473669
30″31586221719361444
LumenArc III24″28147185447299349
30″22645136604890222
LumenMax (Large)24″32886219548391383
30″27630172026159270

In addition to knowing how much light is incident on a given area, we could also look at how much loss of light occurs on a given area when moving the lamp and reflector higher. Table 5, presents the % of light lost on a specified area as one moves the lamp/reflector from 24″ to 30″ above the surface. A higher % loss would indicate that the reflector is creating a larger spread with an increase in distance.

Table 5: Percent of PPFD lost from 24″ to 30″ from the lamp
3×3′ Area2×2′ Area1×1′ Area
Lumenmax Elite12.4816.824.6
LumenBrite11.521.430.5
Lumenarc III19.526.333.0
Lumenmax (large)15.921.626.6
figure1_lumen_max_eliite_top.jpg

Figure 1: LumenMax Elite

figure2_lumen_max_eliite_par.jpg

Figure 2: LumenMax Elite

figure3_lumen_max_eliite.jpg

Figure 3: LumenMax Elite

figure4_lumen_brite_top.jpg

Figure 4: LumenBrite III

figure5_lumen_brite_par.jpg

Figure 5: LumenBrite III

figure6_lumen_brite.jpg

Figure 6: LumenBrite III

figure7_lumenarc_iii_top.jpg

Figure 7: LumenArc III

figure8_lumenarc_iii_par.jpg

Figure 8: LumenArc III

figure9_lumenarc_iii.jpg

Figure 9: LumenArc III

figure10_lumen_max_large_top.jpg

Figure 10: LumenMax (large)

figure11_lumen_max_large_par.jpg

Figure 11: LumenMax (large)

figure12_lumen_max_large.jpg

Figure 12: LumenMax (large)

Discussion

Reflectors are typically designed taking into account 2 conflicting design criteria – focus and spread. Given that a lamp is only emanating light at a certain fixed rate, the light from the lamp is gathered by the reflector and can either be focused to give a higher intensity over an area or spread out to give a large coverage albeit at lower light intensity. Light levels at any given point can also be influenced by changing the distance from the light source by raising or lowering the reflector. So saying one reflector is better than the other is not a trivial task and may even be meaningless, without taking into account the need of the user and the designer’s intent along with the physical constraints of the application. Choosing a reflector often requires taking into considerations the tank dimensions, aquascaping within the tank, the type of corals in the tank and their light requirements, cost budget, space available for mounting, etc.

The reflectors seem to fall into 2 separate groups, Group 1, the Lumenarc and the Lumenmax and Group 2 comprising Lumen Brite and Lumenmax Elite. The Group 1 reflectors seem to be better at providing a wider coverage, whereas the group 2 reflectors tend to focus the light slightly more creating higher peak values and smaller spread.

The lumenarc III and the Lumenmax reflectors provide a large area of light coverage and hence are more suitable for tanks wider than 3 ft. At similar distances they both provide a large coverage of area where the PPFD values reach between 100-200 micromoles/m2/sec. In my experience, if a user can achieve PPFD values of 75-100 at the bottom of the tank, then they will have enough gradation of light in the tank to find places to keep most photosynthetic corals happy in the tank. The Lumenmax reflector at 30″ provided a larger area where the PPFD values were greater than 200, as compared to the Lumenarc reflector. Hence, the reflector will be able to provide a higher intensity deeper in the tank, thus making it a better choice for someone looking to light a wide tank that is deeper than 30″, or for providing the ability to grow higher light corals lower in the tank.

The Lumenbrite and Lumenmax elite are more suitable for tanks 3ft or less in width. They tend to provide a more focused coverage and higher peak values than the Lumenmax and Lumenarc reflectors. This can allow for better use in taller tanks, as more light can reach the bottom, or allow for higher placement of the lights thus reducing the heat dissipating in the water, or allow for higher light values to be obtained lower in the tank. This would allow the user to create a reef with a much lower rock profile. On shallower tanks 24″ or less these reflectors would easily allow the user to move from a 400W lamp to a 250W lamp, resulting in savings in electrical costs.

Conclusions

Reflector design for reef aquariums has improved considerably allowing for more efficient use of light. With these reflectors we can now light reef aquarium with fewer lamps, get deeper light penetration over larger areas. As an example, I am currently lighting my 500G reef aquarium (84″LX48″WX30″D) with just 3 400W metal halide lamps in Lumenarc reflectors with no supplemental lighting. All of these reflectors help shatter the age old paradigm of having one metal halide lamp for every 2 sq feet of surface area. At the time my aquarium was set up, there was no other choice for reflectors. The new reflectors Lumenmax, Lumenmax Elite, and Lumenbrite have added to the choices available. They are all excellent choices, given that these reflectors are fairly close in performance to each other within their designed scope the selection would have to come down to other factors as well – such as construction quality, size constraints, space available for mounting, aesthetics, cost and availability. It is my hope, that the readers would use the data to choose the reflector that best suits their needs, rather than to promote reflector A as being better than reflector B.

Acknowledgements

I would like to thank several people whose help made this study possible. They were kind enough to provide us with lamps, reflectors and ballasts for testing: Ushio Lighting, Icecap, Sunlight Supply, Pacific Garden Supply, and Reef Exotics.

References

  1. Joshi, S. and Marks, Timothy. 2003. Analyzing Reflectors: Part I – Mogul Reflectors http://www.advancedaquarist.com/issues/mar2003/feature.htm
  • Sanjay Joshi

    Sanjay Joshi in real life is a Professor of Industrial and Manufacturing Engineering at Penn State University. He has been a reef addict since 1992, and currently keeps several reef aquariums at home including a 500G SPS coral dominated reef. He also co-manages the 500G aquarium at Penn State. He has published several articles in magazines such as Marine Fish and Reef Annual, Aquarium Frontiers, Aquarium Fish, and Advanced Aquarist. In addition, he has been an invited speaker at several marine aquarium society meetings in the US and Europe. He received the MASNA award in 2006, for his contributions to the marine aquarium hobby.

0 Comments

Submit a Comment

Your email address will not be published. Required fields are marked *