Product Review: Barrier Reef Aquariums' EverGrow Nova A4 LED Light
How time flies. It has been seven years since I wrote a product review on the first commercially available LED lighting system (PFO's Solaris). That article created a lot of controversy, and blogs & billboards were alive with opinions on LED lighting. Since then, the detractors from the ability of LEDs to maintain the health of corals in captivity have been proven wrong, and this form of lighting has gained wide acceptance within the hobby. And, as popularity grows, prices continue to fall.
This month's review is that of the EverGrow Nova A4 LED luminaire customized with LEDs selected by Barrier Reef Aquariums of Seattle, Washington.
I have accumulated a number of LED units in my bone yard over the years, and failures are usually due to fan or power supply failures. Disappointed by the longevity of some LED luminaires on the market, I decided some time ago to discontinue LED product reviews unless the product met certain criteria, such as:
- Product performance (light intensity, spectral characteristics)
- Parts are easily replaceable
- Strong warranty
- Affordable price
This unit meets all these, and this article will relay general observations as well as results of lab testing.
- Dimensions: 11" x 11.5" x 2.5" (28cm x 29cm x 6cm)
- 51 LEDs total - 12 LEDs in four 4" clusters, plus 3 moonlight (blue)
- Electrical cord length: Approximately 6 feet
The Nova A4 luminaire has an adjustable spectrum - there are two control channels. One controls white and 'color' LEDs and the second adjusts the royal blue LEDs. The LEDs in this unit possess some interesting spectral characteristics.
- 13 - 12000K white
- 2 - 6500K white
- 4 - 420nm violet
- 21 - 450nm royal blue
- 4 - 470nm blue
- 2 - 520nm green
- 2 - 660nm red
Actual Spectral Characteristics
The Spectral Power Distribution (SPD) shows the LEDs' outputs are almost exactly as advertised.
Violet light is important in the promotion of photosynthesis as well as corals' production of fluorescent and non-fluorescent proteins. See Figure 1.
450nm 'Royal Blue'
These LEDs produce light peaking at ~443nm. See Figure 2.
These 4 blue LEDs produce light peaking at 469nm. See Figure 3.
Two green LEDs produce light peaking at 513 - 515nm. See Figure 4.
Two LEDs in this fixture produce red light at ~660nm. See Figure 5.
The spectral characteristics of the two types of LEDs (6,500K and 12,000K) are fairly similar, and Figure 6 is typical of these.
Overall Spectral Power Distribution
As would be expected with a luminaire utilizing many blue LEDs, the spectral is skewed towards the violet/blue portion of the spectrum. See Figure 7. Figure 8 shows the composition of the light in a pie chart, and Table 1 shows this information numerically. Figure 9 and Table 2 shows spectral characteristics in 10 nanometer increments.
Modes of Operation
Several modes of operation are available for this light. For those light-hungry plants and animals, the 'Sunny' mode is the ticket - these LEDs can generate light intensity exceeding sunlight (when the PAR sensor is placed just a couple of inches from the light.)
The 'cloudy' mode decreases light intensity by about 40% (compared to the 'sunny' mode.)
The 'moonlight' mode activates 3 blue LEDs to simulate moonlight (with a PAR value of less than 1 µmol·m²·sec.)
A 'manual' mode allows dimming of light in two channels (one channel is for the 21 LEDs producing light peaking at 450nm and the other dims all others.) This feature allows an infinite tuning of spectral characteristics and light intensity.
Power consumption was measured in 3 operational modes. Power draw by the built-in control panel was determined as well (no lights or fans on). These are the figures:
- "Sunny" Mode: 107 watts @0.89 amps, and 119.7 volts
- "Cloudy" Mode: 55.7 watts @0.47 amps, and 120.3 volts
- "Moon" Mode: 3.1 watts @0.04 amps, and 120.6 volts (3 blue LEDs only)
- Control Panel: 2.2w @ 0.03 amps, and 120.3 volts
The LEDs in this luminaire are apparently under-driven. See Figure 11 for a graph of these numbers.
Light Intensity and Distribution Pattern
Light distribution patterns are rarely, if ever, uniform across a given area, and light produced by this fixture is no exception. See Figure 12. These measurements were taken with a Li-Cor Li-1400 quantum meter and Li-192 quantum sensor at a distance of 3.5 inches below the fixture. Recall that maximum sunlight intensity is ~2,000 µmol·m²·sec - this fixture approaches this value under these circumstances.
Light penetration into the water column is important and this fixture does an exceptional job in this respect. See Figure 13.
A remote control device is included with the Nova luminaire. It provides a convenient means of programming the fixture, as well as an off/on switch. The white buttons on the controller are phosphorescent - they slightly glow a greenish color in conditions of low light. This thoughtful touch makes the controller easy to use when programming even in low light conditions. See Figure 14.
PAR Measurement Comparisons - Li-Cor and Apogee Quantum Meters
Serious hobbyists might use a PAR meter to determine light intensity when installing this fixture. Few will have the luxury of a 'lab grade' quantum meter, such as that made by Li-Cor Biosciences and will instead use a less expensive device (such as that made by Apogee Instruments). I compared the measurements obtained through use of these meters, and found that the Apogee meter (when in 'electric light' mode) reported a value ~15% higher than those made with the Li-Cor. See Figure 15.
Recommendation and Discussion
This LED fixture offers impressive performance at a reasonable price. The customized spectrum produced by the LEDs is interesting in that it is not the standard mix of blue and white LEDs. The addition of violet light (at 420nm) and green (at ~515nm) provides a visually balanced spectrum (as well being able to promote photosynthesis. The photopigment peridinin found in zooxanthellae absorbs green light - this is the reason zooxanthellae are brown). The light is intense enough to allow the fixture to be positioned well above the aquarium, where it is less likely to be subjected to water splashes and salt spray. However, the housing is made of a ferrous material and a protective coating of clear polyurethane or car wax (or both) is recommended for protection. Barrier Reef Aquariums recommends one of these fixtures for every 20 inches of aquarium length (approximately).
The amount of light produced by this fixture is remarkable and can certainly meet requirements of the most demanding corals. In fact it can easily exceed their needs and care should be used when mounting it above the aquarium. Figure 13 shows the PAR values at various depths (the fixture is 6.5 inches above water level). Most corals need only 200 - 300 µmol·m²·sec in order to saturate photosynthesis (where increasing the amount of light will not increase the rate of photosynthesis.) Mounting the fixture at least a foot or so above the aquarium is probably a good idea but monitor the corals for any signs of distress. Using the dimming feature is another option. Remember that an Apogee PAR meter reports values about 15% higher than that of a 'lab grade' quantum meter.
At the time of this writing, the retail price is $299.99 US, and includes shipping to addresses in the continental US.
Contact and Ordering Information
Orders can be placed on Barrier Reef Aquariums' website: http://www.barrierreefaquariums.com/
Questions can be addressed by phone: (425) 277-7670 or by e-mail: firstname.lastname@example.org
If you're in the Seattle area, visit them at: 1717 NE 44th Street, Suite A, Renton, Washington. They're behind the Impressions Dentistry office.
Barrier Reef warrants that EverGrow's products will be free of defects for a period of 2 years, in either workmanship and/or defective components. Failures due to abuse, moisture, and improper ventilation are not covered. Proof of purchase is required.
Barrier Reef will repair the unit in-house, or, as an option, supply parts for repair by the owner. I wondered how difficult a replacement of a fan or power supply would be, so I opened the unit up for a look (see Figures 16 and 17.)
Upon inspection, I determined replacement of a cooling fan or power supply is something any handy aquarist should be able to do. All that is required is a Phillips head screwdriver, wire stripper (a single edge safety razor blade will do in a pinch), and electrical tape.
This product complies with the following standards:
ISO Certification (International Organization for Standardization): Based in Switzerland, ISO (International Organization for Standardization) is an international quality management system. Companies can achieve ISO9001:2008 certification when they meet certain standards. Compliance helps ensure constantly reliable products.
CE: A marking required by the European Commission for many products marketed in the European Economic Area, or EEA. This marking means the product conforms to safety, health and environment protection standards of the European Commission.
RoHs is the abbreviation for Restriction of Hazardous Substances Directive (in electrical and electronic equipment) in the European Union (EU). Lead, mercury, cadmium, chromium (hexavalent), polybrominated biphenyls (PBBs) and polybrominated diphenyl ethers (PBDEs) content are regulated by RoHs.
The Shenzhen Sanxinbao Semiconductor Lighting Co., Ltd was founded in 2006, and its operations are ISO 9001:2008-certified. Their products comply with CE standards and the RoHS Directive (see above.)
Photosynthetically Active Radiation (PAR) measurements were determined through use of two quantum meters (LI-1400 data logger and underwater quantum sensor (Li-Cor Biosciences, Lincoln, Nebraska, USA), and a MQ-200 and underwater sensor (Apogee Instruments, Logan, Utah, USA).
Light attenuation was determined with a Li-Cor underwater quantum sensor (calibrated for 'air' and 'water' where appropriate) mounted on a specially built jig. The sensor was lower incrementally into a black polyethylene drum filled with freshly mixed artificial sea water.
Spectral characteristics were made by a fiber optic spectrometer and related software (model USB2000 spectrometer and SpectraSuite software, Ocean Optics, Dunedin, Florida, USA).
Power consumption measurements were made with an electricity usage monitor (Kill-A-Watt meter, P3 International, New York, New York, USA).