The history of reef keeping is
replete with examples of reef keepers adapting methods and tools of
other disciplines for use in a reef tank. Lighting is the most
obvious example- very few of the bulbs we use were designed with reef
keeping in mind. Many less obvious examples abound. A resourceful reef keeper probably
spends as much time in a hardware store as he does in an aquarium store. One of the
undervalued resources available to hobbyists is the boat supply store.
Companies like West Marine can provide a wide range of
products specifically designed for saltwater use. During a visit to my local West Marine I
became curious about bilge pumps. Their reasonable price combined with high volume pumping
capabilities intrigued me. I wrote a piece on using bilge pumps for water circulation in a reef tank. I pointed out
that while powerheads were a convenient means for generating water circulation, their
design created problems when trying to create realistically strong water motion in the
average tank. At subsequent presentations at the Ft. Lauderdale MACNA, Monterey Western
Marine Conference, and several club meetings I talked about bilge pumps and showed a
modification of a pump replacing the impeller with a radio controlled powerboat propeller.
Using video tape presentations I showed that replacing the impeller with a propeller
created a much broader wave-front than the typical powerhead and that much higher water
motion energies could be created without the dangerous shearing forces of powerful powerheads.
Proud sponsor of this column
The idea of using a propeller
came from a science project book (Build Your Own Underwater Robot by Harry Bohm and Vickie Jensen) that used modified bilge pumps to
power and navigate an underwater ROV. (Craig Bingman commented about using propellers
in a reef tank in 1997 and 1998Aquarium
Frontiers columns)
Figure 2: Velocity Comparison
Unfortunately there are several limitations
with bilge pumps. They are inexpensive but not particularly well built. They are not
designed for continuous use. Finally, most bilge pumps run on 12 volts. Despite these
limitations, the article and presentations generated considerable on-line discussion, and a
number of hobbyists began experimenting with the modifications.
One hobbyist in particular, Jimmy Chen, was
intrigued enough with the concept to search for means to overcome the limitations of bilge
pumps. His efforts have produced a practical product that dramatically improves on my
original concept. The design is a significant improvement over traditional means of
creating water motion in a reef tank and warrants the attention of every reef hobbyist.
The key component is the Little Giant series
of pond pumps. These submersible pumps are similar to bilge pumps in that they are direct
drive pumps with an impeller mounted on the end of a shaft. The difference is that the
pump runs on house current and is designed for continuous use. Mr. Chen's modification
involves replacing the impeller with a propeller (figure 1). The modification kit sold by
Mr. Chen includes the prop and mounting brackets so that the pump can be mounted on the
side of the tank like a traditional powerhead (see www.reeftec.com
for further details, forthcoming at the time of this writing). Chen has successfully
modified the Little Giant PE-1, PE-2, and the PE-2.5.
Figure two compares the velocity of the Gemini air-cooled
powerhead to the modified PE-1 at increasing distances from the nozzle. Readers of this
column know that the Gemini is one of the most powerful powerheads
sold to the hobby and it is one that I have frequently recommended. On the face of it, the graph
suggests that the Gemini is a much more powerful pump. At each distance the velocity of
the water flow from the Gemini is greater than that of the PE-1. Rather than proving the
superiority of the Gemini pump, however, the graph shows the limitations of using a
velocity meter to measure water motion in a reef tank. Because water flows from the Gemini
pump through a fairly narrow nozzle, the velocity of water of a given volume is high. In
contrast, the same volume of water flows through a propeller at a slower rate because of
the larger cross section of the propeller.
Proud sponsor of this column
To better determine how the
two pumps compare in a reef tank, the modified Little Giant PE-1 pump was mounted fairly
close to the surface at the same depth as the output of the Gemini. This is one limitation
of a air cooled powerhead. The water is circulated fairly close to the surface. This can
give the illusion of good water motion while producing considerably less at depth where it
is needed. In my 55 gallon test tank the Gemini generates a modest but reasonable roil
(turbulence) at the surface. Most of the flow from the pump moves directly across
the tank. At the same depth, the Little Giant prop produces a very high surface wave front
across the length of the tank accompanied by considerable splash. This suggests that water
flow from the propeller is spreading outwards at a much faster rate than the flow from the
Gemini.
Figure 3 shows water motion using four
different devices. In each case one pump is turned on and then water motion allowed to
stabilize. A "typical" position of the test strips is shown. (Even with a
continuously running powerhead, there is enough turbulent flow in the tank to change the
position of the test strips from time to time, so there is some subjectivity involved in
choosing the "typical" view.) For these tests, the Little Giant pumps were
mounted about five inches below the surface of the water. The top frame demonstrates the
effect of one Otto 2000 running in the forward right hand corner. The second frame is the
effect of the Gemini running in the front left corner. The third frame is the PE-1 in the
left rear corner, and fourth frame is the PE-2 in the right rear corner.
Figure 3. Water motion demonstrated with four different devices. Top from
left: first frame, second frame. Bottom from left: third frame, fourth frame.
The Otto powerhead is rated at
500 gph and mounted close to the surface gives the illusion of generating a great deal of
water motion. As the photo shows, however, the Otto barely moves the test strips. The
unidirectional flow is apparent from the fact that the front row of strips is deflecting
while the rear row is fairly upright. The greatest flow is at the center of the tank. The
strips near the powerhead are stationary because the jet of water is flowing over them.
The Gemini in the second frame deflects the test strips very differently. Greatest
deflection is at the opposite side of the tank towards the powerhead. Water is bouncing
off the opposite side of the tank and deflecting the strips away from the glass. Water
motion is lowest nearest the pump. One other interesting observation is the deflection of
both rows of test strips. As the water bounces off the side of the tank it spreads towards
the rear of the tank.
The pattern of deflection of the PE-1 is
similar to the Gemini in some respects. The strips furthest from the pump deflect the most
and deflect towards the pump. One difference is that the strips closest to the pump are
deflecting more with the PE-1 than the Gemini. What is interesting is that the Gemini is
rated at 960 gph while the PE-1 is rated at 170 gph. A pump rated at less than 20% the
flow of the Gemini appears to be generating as much turbulent flow as the Gemini. The PE-2
in the bottom frame generates the greatest flow nearly flattening the test strips on the
opposite side of the tank.
The strong flow of the PE-2 inadvertently
demonstrated another difference between a powerhead and the prop. In the first few tests I
used insufficiently weighted strips and the flow was sufficiently great enough to push all
of the test strips to the right side of the tank. A powerhead like the Gemini would have
drawn the strips into the impeller of the pump. Any hobbyist who has had anemones, snails,
or other invertebrates drawn into powerheads knows the effect. Instead of drawing the
strips into the propeller, the propeller appeared to create a zone around the rear of the
prop that kept the strips away. While the final version of the mounting bracket includes a
shield to keep animals away from the spinning propeller, the danger seems to less than it
might first appear.(To test this I have been running both modified bilge pumps as well as
the Little Giant based devices in my main display tank between tests. No animal has
approached or been drawn into the propeller.)
Mr. Chen is selling the prepared propeller
and mounting bracket that accommodates either the PE-1 or PE-2 as a kit. A hobbyist then
buys a pump of his choice and makes the modifications. It took me about 15 minutes to
modify each pump. A pair of PE-1 pumps should be more than adequate for a 90 gallon tank
and depending on lay-out, a combination of a PE-1 and PE-2 should work in a 90 gallon tank
unless the tank has very fine sand. Larger tanks that would normally use a multiple Tunze
or Gemini pumps as I did in my 300 gallon tank would want to use at least a pair of
modified PE-2 pumps.
Any hobbyist who is reasonably adept at cutting and
gluing acrylic can duplicate the modification kit. On the other hand, supporting
innovators like Jimmy Chen by buying the kit from him encourages Chen and others to
continue to innovate. The hobby needs more Jimmy Chens and the hobby should support those
like him. European reef hobbyists and companies once led the way in reef keeping
innovation. North American reefkeepers have closed the gap, and these efforts should be
encouraged and supported. The most recent evidence that innovation is now flowing from the
New World to the Old is the announcement at the recently concluded Interzoo that Tunze
will begin producing a new series of nozzle-less pumps for water motion. Seems hobbyists
are not the only readers of American on-line discussion groups.
